Über Rollgabelschlüssel

Aus WikiPedalia
Hinweis
Dieser Artikel stammt im Original aus dem Juni 1982 und erschien im Bicycle Magazine.
Ergänzung aus dem Jahr 2010 von John Allen: Viele Fahrräder haben inzwischen überwiegend Schnellspanner und Inbusschrauben im Einsatz. Aber selbst wenn man so ein modernes Fahrrad fährt, ist das Mitführen eines Rollgabelschlüssels kein Fehler, um jemndem im Notfall zu helfen. Ein 35 cm oder 45 cm langer Rollgabelschlüssel ist ein nützliches Werkzeug für den Heimschrauber, um einen universellen Steuersatzschlüssel zu haben oder einen Freilaufabzieher zu drehen. Er hat auch genug Hebelwirkung, um einen Kassettenlockring zu bewegen oder eine Innenlagerschale zu lösen.


Dies ist der  erste einer Serie von Artikeln, die von Zeit zu Zeit erscheinen werden, in denen Vorgehensweisen zum richtigen Werkzeugeinsatz diskutiert werden. Der Autor Sheldon Brown beginnt hier mit den Rollgabelschlüsseln; er hat uns zugesichert, dass in späteren Artikeln nach und nach höher spezialisierte Werkzeuge diskutiert werden. Seine Sie nicht hochnäsig, wie Brown ausführt steckt mehr in einem Rollgabelschlüssel als die meisten Leute vermuten.

Brown - regelmäßigen Lesern für sein Meisterstück über Laufradbau aus dem Jahr 1981 bekannt - war der Chefmechaniker von Bicycle Revival, einer Fahrradladenkette mit mehr als 15 Fahrradgeschäften in der Gegend von Boston. Zehn Jahre lang hat er "Wie man sein Fahrrad selbst repariert" am Boston Center for Adult Education (Boston Zentrum für Erwachsnenbildung) gelehrt. Er ist Mitbegründer der Bicycle Repair Collective in Cambridge.

Der Herausgeber (John Schubert)
Rollgabelschlüssel im Einsatz

Rollgabelschlüssel

Das grundlegendste Fahrradwerkzeug ist ein kleiner halbmondförmiger Rollgabelschlüssel. In einer gut ausgestatteten Werkstatt wird das Werkzeug nicht oft zum Einsatz kommen, hat jedoch unterwegs einen vielseitigen Einsatzbereich. Sheldon Brown empfahl, immer einen Rollgabelschlüssel dabei zu haben, wenn man unterwegs nicht zu Fuß zurück laufen möchte. Mit diesem Werkzeug kann man an einem durchschnittlichen Fahrrad mehr Dinge reparieren als mit jedem anderen Werkzeug. Rollgabelschlüssel gibt es in den Größen 4, 6, 8, 10, 12, 15, 18 und 24-Zoll. Der 4 Zoll (10 cm) Rollgabelschlüssel ist nur sinnvoll bei neueren modischen Fahrrädern, bei denen es Schnellspannachsen an Laufrädern gibt, deren Muttern 14 oder 15-Millimeter messen. Selbst wenn der Schlüssel passt, hat man mit dem 10 cm langen Griff meistens nicht genug Hebel, um als Person mit normaler Handkraft eine Mutter fest genug anzuziehen. Das gilt auch für Lenker- und Satteljustage. Wenn Dein Fahrrad also eine Schnellspannachse und Inbusschrauben an Lenker und Sattel hat, ist der 10 cm Rollgabelschlüssel ein nützliches Werkzeug auch für Einstellarbeiten an Bremse und Kettenschaltungskomponenten. Gleichzeitig kann man mit ihm auch Anbauteile wie Gepäckträger, Flaschenhalter und Beleuchtung befestigen.

Transportable Größe

Die praktischste Schlüsselgröße für den Transport am Fahrrad ist 6-Zoll (15 cm). Abhängig von der Marke, kann man einen 15cm Rollgabelschlüssel mindestens 19 Millimeter oder etwas mehr öffnen. Damit öffnet er weit genug, um außer am Steuersatz und den Innenlagerschalen alle Muttern greifen zu können. Der Griff ist lang genug, um einer Person durchschnittlicher Stärke, genügend Hebel zu bieten, alles, was in das Maul des Schlüssels passt, festzuziehen.

Ein Fahrradfahrer mit unterdurchschnittlicher Kraft kann Bedarf nach dem Hebel eines 8-Zoll (20 cm) Rollgabelschlüssels haben, um auch Achsmutter und Sattelklemmmuttern fest genug anziehen zu können. Die 20 cm Version des Rollgabelschlüssels hat als einzigen Vorteil den zusätzlichen Hebel, denn obwohl der Schlüssel weiter öffnet als die 15 cm Version, passen dennoch die teile, die ein 15 cm Schlüssel nicht packt auch die 20 cm Version nicht. Zudem passt die 20 cm Version nicht in kleine Werkzeugtaschen und wiegt ein gutes Stück mehr als die 15 cm Version.

In der Werkstatt

Für den Einsatz in der Fahrradwerkstatt geben die 12- und 15-Zoll (30 und 38 cm) Versionen gute Universalwerkzeuge für Steuersatzarbeiten ab. Ist es die Absicht, ein Werkzeug als Steuersatzschlüssel zu haben, ist der Einsatz der Variante mit dem 90° abgeknickten Kopf (im Original: Monkey Wrench oder Spud Wrench) zu kaufen, weil die Standardversion des Rollgabelschlüssels den Werkzeugkopf nur etwa 30° zum Griff abgeknickt hat. Ein Großer 90° Rollgabelschlüssel ähnelt stark einer Rohrzange mit weichen Klauen und ist ein guter Universal-Steuersatzschlüssel und kann auch gut eingesetzt werden, um verbogenen Schaltwerke und Kettenblätter zu begradigen.

Ergänzung von John Allen
John Allen bevorzugt die 38 cm Version, weil er einen längeren Hebel hat und besser als Griff für einen Freilaufabzieher dienen kann.


Vor- und Nachteile

Auto and motorcycle mechanics usually have a very low opinion of adjustable wrenches. They say that you should use a set of fixed-size wrenches instead. This is not always practical for bicycle work. When you travel under your own power, there is a limit to how many wrenches you want to carry around with you, and there is also the problem of lack of standardization.

There are three major systems of wrench sizing: Metric, U.S. Standard (S.A.E.), and Whitworth (British). To be ready for anything, you would need three complete sets of wrenches, as there is very limited interchangeability among these systems. The Whitworth system has been out of use since the 1970s, because of Britain's adoption of the Metric system, but there are still many older British-made bicycles on the road with Whitworth parts. U.S. Standard sizes are used on many parts of American-made accessories and older American-made bicycles, but American bikes almost always have foreign-made parts -- at least the brakes and derailleurs -- that require Metric wrenches. Bicycles made in Europe or the Orient will usually be all Metric, at least as far as wrench sizes are concerned.

There is some disagreement over which is the better direction to use a Crescent-type wrench -- whether the moveable jaw should be on the "pushing" side or the "pulling" side; I have taken part in long debates on this subject, and I know excellent mechanics on both sides of the question. In practice, however, it makes no real difference if you are using a wrench of good quality. Which way to put the wrench on should be determined by the accessibility of the nut or bolt you are trying to turn. In tight spaces, such as adjusting a seatpost bolt on a bicycle with a low saddle and a rear carrier, it may be necessary to keep flopping the wrench over, turning the nut 1/12 turn with each fetch.

Adjustable wrenches used carelessly can cause damage to nuts and bolts and injury to your hands, so it's very important to use them properly. Try to place yourself so that you can turn the wrench by pulling on it, rather than pushing. If you push on a wrench and it slips off of the nut, you are very likely to wind up punching something hard with your fist. This is why adjustable. wrenches are sometimes called "knuckle-busters." The other common mistake people make with adjustable wrenches is to be careless in adjusting them. Every time you put the wrench on a nut, turn the adjusting screw with your thumb while lightly rocking the wrench back and forth, to make sure that the wrench is adjusted for as tight a fit as possible on the nut. This is necessary because each time you take the wrench off the nut and put it back on, it loosens up a little bit. If you don't re-tighten the screw, the wrench will loosen up and slip off the nut when you try to turn it. This may damage your hand, and will certainly damage the nut, by rounding off its corners; then no wrench will fit the nut properly.

Eine lohnende Investition

You can buy a 6-inch Crescent-type wrench for as little as a couple of dollars, or your can spend up to $8 for one that, at first glance, looks identical. In this case, however, the "bargain" is no bargain. To be reliable, a wrench must be made from the finest chrome-vanadium steel. One way to judge the quality of a wrench is by weight-- the cheap ones are heavier because they are thicker. This is an attempt to make up in quantity of metal what they lack in quality. If you buy a cheap wrench, it may work all right for a while, but with time and use, the jaws will bend so that they are no longer parallel. Once this happens, the wrench will never fit anything properly -- you will have to throw it away and buy another.

If you buy a good-quality wrench, it should last indefinitely. The better brands come with a lifetime guarantee. In particular, the Craftsman line from Sears Roebuck and the Blue Point from Snap-on have a lifetime guarantee that is good anywhere in the United States. If you have a broken Craftsman hand tool, you can take it to any Sears store for a free, no-hassle replacement.

The same is true of Snap-on, except that Snap-on has no regular retail stores. Snap-on tools are sold out of big white vans that are rolling tool shops. These vans have regular routes, primarily selling to garages. If you are riding by and see one of these trucks parked, stop and talk to the driver, who will be glad to give you a catalog and sell you any tools you want.

Snap-on tools are very expensive, but they are also the very best. The Snap-on Blue Point 6-inch adjustable wrench is the lightest I know of, weighing 100 grams, compared with 125 grams for the average good-quality unit. It also opens wider than most.

Quelle

Dieser Artikel basiert auf dem Artikel Tool Tips Adjustable Wrenches von der Website Sheldon Browns. Originalautor des Artikels ist Sheldon Brown.